Top 10 common forklift mishaps ， forklift operation ought to take note of these matters ！.

Do not underestimate the forklift at work. If the procedure is not good, there will certainly be severe crashes in minutes, and there are several accidents including forklifts.

Instance 1: The forklift freight obstructed the chauffeur's sight, and the person in front might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising heavy products, the employees used their body weight as the counterweight, which nearly triggered casualties.
Situation 3: The width of the forklift cargo surpasses the permitted size of the route and hangs on the roadside rack, which practically triggers an mishap.
Case 4: Forklift is speeding and surrender throughout a turn.
Instance 5: The forklift chauffeur did not observe the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees illegally, the forklift chauffeur does not put on the seat belt, the forklift lifter falls and the motorist is crushed when the forklift surrender.
Instance 7: The forklift chauffeur did not put on a safety belt and dropped from the vehicle when it rolled over and was squashed.
Forklift operation should pay attention to these matters ：.

Beginning.
1. Before starting, observe the surroundings, and after verifying that there are no challenges that prevent the security of driving, honk the horn first and after that begin.
2. For vehicles with hydraulic (air pressure) brakes, the brake hydraulic pressure (air pressure) scale need to be risk-free before beginning.
3. When the forklift starts with a load, the vehicle driver needs to initially validate that the tons is steady and trustworthy.
4. The beginning should be sluggish and constant.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the pole must be slanted in reverse. .
2. Do not lift the fork expensive when driving. When going into and leaving the job website or while driving, be careful that there will be no barriers in the sky. When the lots is taking a trip, the fork has to not be increased too high, which will impact the stability of the forklift. .
3. After discharging, the fork should be reduced to the typical driving position before driving. .
4. When transforming, if there are pedestrians or cars nearby, the driving signal should be provided initially. High-speed doglegs are banned. High-speed doglegs will certainly create the lorry to lose lateral stability and tip over. .
5. When the forklift is downhill, it is purely forbidden to shut off the fire and slide, and it is forbidden to brake suddenly while driving with loads unless there are unique conditions.
6. When the forklift is running, it must follow the web traffic rules in the manufacturing facility and have to keep a particular safety distance from the car in front. .
7. When the forklift is running, the lots has to remain in the most affordable position that does not hinder the driving, and the gantry ought to be correctly tilted back. The tons shall not be raised except when stacking or loading. .
8. The height of the lots have to not obstruct the vehicle driver's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when reversing.
9. It is restricted to activate the ramp, neither to drive across the ramp. .
10. The risk-free driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive securely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is lifted, lifted or driven, it is forbidden for personnel to depend on the fork to hold products and play a balancing role. .
12. If troubles are discovered, they will be repaired and reported in a prompt way, and they will never ever operate with illnesses or hide them.

packing and discharging.
1. When fork-loading items, the range between both forks must be changed as needed to make the tons of the two forks well balanced and not skewed, and one side of the item need to be against the shelf. .
2. It is prohibited to work with a solitary fork or utilize a fork top or draw. In unique circumstances, safety and security warning signs must be established to remind bordering pedestrians. .
3. In the process of loading and discharging items, the forklift has to be braked with the brake. .
4. The rate of the car need to be sluggish and constant. Beware not to roll the wheels on the dunnage, so as not to extend the rolled objects and injure people. .
5. When making use of a fork to fork the goods, the fork should be as deep as feasible under the tons, and it needs to be noted that the fork idea should not touch various other items or objects. The tons should be supported with marginal back tilt of the gantry so that the tons does not slide in reverse. The pole can be tilted ahead a little when the load is reduced to permit very easy placement of the tons and removal of the forks. .
6. It is forbidden to fork goods at broadband and ram hard objects with the fork head. .
7. When the forklift is working, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the Stand-on Electric Pallet Stacker goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to raise personnel to engage in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not permitted to use the brake inertia to slip, put, round or roll objects. .
10. It is not Stand-on Electric Pallet Stacker enabled to utilize forks to choose, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the parking brake deal with to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for special circumstances, such as the chauffeur does not leave the car's line of sight and does not exceed 1 minute).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance should be checked, and gas, lubing oil and air conditioning water ought to be added.
2. Check the safety efficiency of beginning, running and braking.
3. Check whether the lights and horn signals are complete and reliable.
4. Throughout the operation of the forklift, check whether the pressure and temperature level are typical.
5. After the forklift is running, the outside leakage needs to additionally be inspected and the seals ought to be changed in time.

Forklift Safety Operation Specifications.
1. You have to inspect before leaving the car;.
2. When you encounter a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the nadir of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the slope is higher than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift personnel bring the goods and move forward, if they come across large or hefty goods and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not permitted.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an challenge on one side of the road, the contrary side of the area with the very same size as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844